...www.microsoft.com/windowsserver2003/technologies/storage/iscsi/iscsicluster.mspx Also ensure the NICs ... we have some weird and unworkable issues since we migrated a fileserver to.... I did not test the performance by iometer or any other tool...with the above counter. Using the iSCSI session counters for Bytes "received/... please. Also as a side issue, after I rebooted the fileserver I...

...>> news:e8Y7Zvv9HHA.1208@TK2MSFTNGP03.phx.gbl... We are running windows 2003 Service Pack 2 along with ISCSI initator 2.05 - Powerpath 4.6.1 attaching to an EMC CX340C all NIC are attached to ... 2%% - 5%% of the NIC card being used (task manager - networking). What type of performance should we see? I am figuring 2%%-5%% is kinda of the low side. ...

Better yet, use DataMover's automated performance tests. There's a 32bit and 64bit version ... a 30 day license to run the automated performance tests. Iometer can't compare to this tool.... running windows 2003 Service Pack 2 along with ISCSI initator 2.05 - Powerpath 4.6.1 attaching... used (task manager - networking). What type of performance should we see? I am figuring 2%%-5...

...> news:e8Y7Zvv9HHA.1208@TK2MSFTNGP03.phx.gbl... We are running windows 2003 Service Pack 2 along with ISCSI initator 2.05 - Powerpath 4.6.1 attaching to an EMC CX340C all NIC are attached to a ...between 2%% - 5%% of the NIC card being used (task manager - networking). What type of performance should we see? I am figuring 2%%-5%% is kinda of the low side. ...

... message news:e8Y7Zvv9HHA.1208@TK2MSFTNGP03.phx.gbl... We are running windows 2003 Service Pack 2 along with ISCSI initator 2.05 - Powerpath 4.6.1 attaching to an EMC CX340C all NIC are attached to a ...between 2%% - 5%% of the NIC card being used (task manager - networking). What type of performance should we see? I am figuring 2%%-5%% is kinda of the low side. ...

...size, etc)? ~kenny Sabo, Eric wrote: We are running windows 2003 Service Pack 2 along with ISCSI initator 2.05 - Powerpath 4.6.1 attaching to an EMC CX340C all NIC are attached to a cisco... between 2%% - 5%% of the NIC card being used (task manager - networking). What type of performance should we see? I am figuring 2%%-5%% is kinda of the low side. Opinions ...

We are running windows 2003 Service Pack 2 along with ISCSI initator 2.05 - Powerpath 4.6.1 attaching to an EMC CX340C all NIC are attached to a cisco 6513 switch... are only seeing between 2%% - 5%% of the NIC card being used (task manager - networking). What type of performance should we see? I am figuring 2%%-5%% is kinda of the low side. Opinions are welcomed. Thanks, Eric...

...> We have purchased a IBM iSCSI SAN but we are experiencing very poor performance from it. The iSCSI...I noticed this section in the iSCSI 2.04 userguide, and I am.... You should check with your iSCSI target manufacture to ensure that ...> problems will likely occur. --- Our iSCSI SAn can only format the ... for help with troubleshooting this performance issue for you. rgds, Edwin....

... cross-over cable to isolate the issue. Then get fast PC, install software iSCSI target wire speed capable (DataCore SANmelody ... are experiencing very poor performance from it. The iSCSI SAN and network runs 1...correctly. You should check with your iSCSI target manufacture to ensure that their ... problems will likely occur. --- Our iSCSI SAn can only format the arrays ...

You had a similar issue? Thanks for the thought! Unfortunately I didn... *seem* to occur if the iSCSI target has been set as a... "Julian" wrote: (Vista HP SP1, iSCSI Target on Thecus N5200Pro) Having found... how to log-off an iSCSI session, I find now that ... being used"; as per Microsoft iSCSI Software Initiator 2.x Users ... are set to "Optimise for Performance", and I'd like to ...