Fadale
  Home FAQ Contact Sign in
 
 Advanced search
MATCHING GROUPS



more...
POPULAR GROUPS

more...
found 669 articles for 0.312 sec
On Mon, 21 Jul 2008 21:56:43 -0400, "Proctologically Violated®©" <entropic3.14decay@optonline2.718.net> wrote: ><brewertr@aol.com> wrote in message >news:b7da84tolbebmomdmo97s24jghpp3h5m40@4ax.com... >> On Mon, 21 Jul 2008 20:51:40 -0400, "Proctologically Violated®©" >> <entropic3.14decay@optonline2.718.net> wrote: >> >>>Awl-- >>> >>>Finally solved sundry Fadal issues. A shout out to Mid     

Group: alt.machines.cnc · Group Profile · Search for Fadale in alt.machines.cnc
Author: brewertr
Date: Jul 21, 2008 19:40

On Mon, 21 Jul 2008 20:51:40 -0400, "Proctologically Violated®©" <entropic3.14decay@optonline2.718.net> wrote: Finally solved sundry Fadal issues. <snip> ======= Thanks for "closing the loop." I always like to hear a story with a happy ending. Are power supply problems becoming more common or am I just noticing these more? It appears that as the price of electricity goes up the quality
Show full article (1.03Kb) · Show article thread
Awl-- Finally solved sundry Fadal issues. A shout out to Mid-Atlantic CNC in NJ, who seem to make some effort to save cnc suckas a few dollars. The machine would alarm out on 3-axis 100%% rapids. It did not do this in NYC when powered by utility 3ph at 208V, despite an incorrect SetP parameter setting for rapids. But apparently, with the crappier power in Yonkers, the incorrect SetP     

Group: alt.machines.cnc · Group Profile · Search for Fadale in alt.machines.cnc
Author: F. George McDuffee
Date: Jul 21, 2008 18:32

On Mon, 14 Jul 2008 15:51:06 -0400, "Proctologically Violated" <entropic3.14decay@optonline2.718.net> wrote: Awl-- Just got off the phone with Fadal. Turns out that if running a 3016L off a rotary converter, there is no easy way to separate the electronic stuff from motor stuff, ie, no easy way to put the electronic stuff on 220/240 single phase, and have the wild leg just go
Show full article (0.86Kb) · Show article thread
Awl-- Just got off the phone with Fadal. Turns out that if running a 3016L off a rotary converter, there is no easy way to separate the electronic stuff from motor stuff, ie, no easy way to put the electronic stuff on 220/240 single phase, and have the wild leg just go to motors. This is because, from the schematic, all three legs go all over the place. The transformer is a 3 ph transformer     

Group: alt.machines.cnc · Group Profile · Search for Fadale in alt.machines.cnc
Author: brewertr
Date: Jul 21, 2008 18:18

"John R. Carroll" <jcarroll@ubu,machiningsolution.com> wrote in message news:SRyck.13429$xZ.9053@nlpi070.nbdc.sbc.com... Black Dragon wrote: Booted up one of the Fadals this morning and was greeted with a battery low warning and had to re-configure the BIOS settings to get it working properly. The lithium battery is soldered to the main-board. <sigh> Has anybody
Show full article (0.38Kb) · Show article thread
On May 28, 12:10 am, "over a barrel" <precisionmachin...@COLDmail.com> wrote: > Loking to replace them all it a 4020 cnc88 might as well go to metric > screws inch serie$ are becoming dinosaur bones if anyone has metric screws > selected in the pramaters then appreciate if you could get a flashlight lean > in there pull back Y telescope and take a calipe reading let me know what > pitch is they     

Group: alt.machines.cnc · Group Profile · Search for Fadale in alt.machines.cnc
Author: Proctologically Violated®©
Date: Jul 21, 2008 17:51

"Mark" <shop@kmcbearings.com> wrote in message news:5JnJj.2033$3N1.1876@newsfe17.lga... "fred" <fmotz@hotmail.com> wrote in message news:LzbJj.8206$CO2.4686@newsfe12.phx... fred wrote: Anyone got a cutter comp code sample, what does a Fadal use for register? My post is out putting a H. Like G41XxxxH8, should H be a D like Fanuc? Thanks
Show full article (2.86Kb)
"fred" <fmotz@hotmail.com> wrote in message news:LzbJj.8206$CO2.4686@newsfe12.phx... > fred wrote: > > Anyone got a cutter comp code sample, what does a Fadal use for > > register? My post is out putting a H. > > > > Like G41XxxxH8, should H be a D like Fanuc? > > > > Thanks > > > > P.S. where has all the CNC talk gone, the group looks like SPAM central > > with all politics etc? Maybe     

Group: alt.machines.cnc · Group Profile · Search for Fadale in alt.machines.cnc
Author: Matt Stawicki
Date: Jul 15, 2008 08:45

Show full article (0.89Kb) · Show article thread
    

Group: alt.machines.cnc · Group Profile · Search for Fadale in alt.machines.cnc
Author: Proctologically Violated®©
Date: Jul 14, 2008 12:51

Show full article (2.38Kb)
    

Group: alt.machines.cnc · Group Profile · Search for Fadale in alt.machines.cnc
Author: over a barrel
Date: Jul 7, 2008 22:31

Show full article (1.77Kb) · Show article thread
    

Group: alt.machines.cnc · Group Profile · Search for Fadale in alt.machines.cnc
Author: WudifCud
Date: May 28, 2008 00:24

Show full article (0.86Kb) · Show article thread
    

Group: alt.machines.cnc · Group Profile · Search for Fadale in alt.machines.cnc
Author: PrecisioNmachinisT
Date: Apr 4, 2008 12:39

Show full article (0.86Kb) · Show article thread
    

Group: alt.machines.cnc · Group Profile · Search for Fadale in alt.machines.cnc
Author: Mark
Date: Apr 4, 2008 03:49

Show full article (0.65Kb) · Show article thread
1 · 2 · 3 · 4 · 5 · 6 · 7 · 8 · 9 · next